8.5L Mini Water Cooler Dispenser All In new ABS Material With Chilling water Function with good sales on Amazon. Please visit the blow link on Amazon from one of our UK customers.
https://www.amazon.co.uk/dp/B078XBL9HJ
https://www.amazon.co.uk/dp/B01NAP7OU5
Products component checklist :
| Number | Products Description |
| 1 | Filter change indicator |
| 2 | Unfiltered water chamber |
| 3 | Filter cartridge |
| 4 | Indicator light |
| 5 | water tap |
| 6 | Drip tray |
Technical and Replacement filters
| | System Specification |
| Electrical Requirements | 220 - 240V , 50/60 Hz |
| Input cooling | 61 Watts |
| Filter replacement model | |
| Filter cartridge life | 150 litres or 2 months |
| Filter cartridge flow rate | 100-400ml/minute |
| Filter reduction capabilities | Chlorine, lead, copper, etc |
| Products weight | 3.2 KGS |
| Total water tank capacity | 8.5L |
| Filtered water tank capacity | 5L |
| Unfiltered water tank capacity | 3.5L |
Sterilising and Cleaning Instructions
It is important to follow the sterilising and cleaning process below before using and as part of your regular maintenance routine:
- Combine two tablespoons of baking soda with 2 litres of lukewarm water in a separate container
- Remove the unfiltered water chamber from the cooler
- Pour the bicarbonate solution into the water chamber
- Press the water dispenser until water pours from the tap
- Cycle the bicarbonate solution through the tap and empty into the top water chamber, Repeat this procedure several times
- Turn on the power and leave for at least 4 hours
- Drain all the bicarbonate solution until empty
- Remove the drain plug from underneath the unit to drain any water or solution in the cooling tank. This is vital to ensure the solution is expelled from the cooler
- While the drain plug is open, rinse the unit with 2 litres of clean water to remove any bicarbonate solution
- Refit the top and water chamber
- Flush clean water through the unit and drain out via the tap, Tilt the unit forward and backward to expell all water from unit
Products simple operation introduction :
Before first use :
- Wash and rinse out the plastic water tanks thoroughly before use
- Remove the filter from its packaging then fully cover and soak in cold clean water for approximately 15 - 30 minutes then rinse off under cold clean running tap water until see the clear water then will start for using
- You may notice a fine black dust come out of the filter, this will happen on all new filters and when water is filtered through it the first couple of uses . This is no cause for alarm . It is just the dust from the activated carbon inside the filter. Although it looks unsightly , it will not harm you.
Prepare Filter
- Remove filter cartridge from plastic cover
- Do not lose the filter cartridge O-Ring
- Soak filter cartridge in water for approximately 20 minutes
- Shake filter while under water to remove dark carbon particles and any trapped air
Insert filter and ensure it sits flat and fully seated
Assembly:
- Ensure Drain Plug underneath unit is secure on the unit
- Place unfiltered water chamber on to the Filtered Water Chamber
- Place Filter cartridge into the unfiltered Water Chamber. Ensure Filter cartridge is secure
- Place top on top of water Chamber
- Turn the switch to "ON" at the back of the unit
- Empty water into the unfiltered water chamber, allow water to run through to the Filtered water Chamber
- Once the Filtered water chamber is filled, push and hold the tap down until water comes out of the tap
When you turn on the switch to " on" at the back of the unit , you will see RED LIGHT indicating the water
cooler is chilling the water . When the indicator light from RED LIGHT to BLUE LIGHT indicating the water
approximatly 800ml cold tank has fully chilled .
Red Light : Water is chilling
Blue Light: The water has fully chilled for drinking
Technical and Replacement filters
Maintenance :
- Replace filter after 150 litres or 2 months of use or whichever comes first
- If the taste , smell or flow rate changes , it is recommended you change the filter immediately
- Sanitise the unit fully every 1 to 2 weeks. This will be based on the customers' requirement.
Notices :
| If the water cooler has not been used for some time , unplug the unit , drain all the water and clean with warm soapy water . Flush the water cooler and empty all water out through the water tap or tearing out the bottom small silicone tube |
Position :
- The unit is designed for light use at home or in a small office
- If the unit is damaged in any way , refrain from using it
- Keep away from direct sunlight
- Ensure the unit is appropriately earthed
- Ensure the unit has 100mm of ventilation all round
- Do not place near a heat source
Contact details:
NINGBO GOOD WATER SOURCE ENVIRONMENTAL PROTECTION ELECTRICAL APPLIANCE CO.,LTD
CONTACT PHONE(WHATSAPPLE): (86) 13884494576
CONTACT E-MAIL: jackliu@miniwatercoolerdispenser.com
WECHAT: Jackliu8886
SKYPE: jackliu06316
Besides, to get more know for our products information, please visit the below link on Amazon from one of our UK customers, thanks!
https://www.amazon.co.uk/dp/B078XBL9HJ
https://www.amazon.co.uk/dp/B01NAP7OU5
Product Tags:
|
|
8.5L Mini Water Cooler Dispenser new ABS Material With Chiller Function with good sales on Amazon Images
|
